Limited current controlling to ensure the best charging effect,maximum protection for batteries.
Large capacity, easy to use.
Suitable for Electric scooters, electric bicycles.
Rated Voltage: 36V~48V
Rated power: 350W
1 X Brushless Controller
1.An easy to use and extremely practical hot stapler kit, designed for repairing plastics.
2.Its simple operation allows practical repairs for many, plastic parts potentially saving them from the scrap heap.
3.Easy to use,very convenient.
Color: Gold silver
1 X Triangular Spatula
1.Overload protection: When the load exceeds the rated load automatically stop working,
protect the product from damage and operator safety.
2.Selection of high-quality four-pole carbon brush 12V DC motor, torque strong, powerful.
Carrying weight dynamic
1: 1.25 times. Static: 1: 1.5 times
Bear 5 Ton
Maximum carrying value
High strength nylon 66
1, electric charge use:
⑴ the car parked on the level of the road, the engine flameout, and do not forget to tighten the hand brake.
⑵ put the electric jack placed in the tires near the body under the steel beam, and the top of the electric jack on the
bottom of the car under the support point, so that the electric jack can be safe and effective lifting.
(3) Connect the electric jack to the 12V power supply in two ways:
① use cigarette lighter connection: one end of the cigarette lighter plug into the cigarette lighter socket,
the other end of the 5.5mm plug into the electric jack on the 5.5mm plug seat. (Note: cigarette lighter fuse rated current shall not be less than 10A)
② Use the vehicle battery to connect directly: Insert one end of the cigarette lighter plug into the cigarette lighter socket at one
end of the battery clamp, and hold the red clip on the other end of the battery clip and hold the battery "+" (positive) Battery "-" (negative) connected,
and then plug the other end of the cigarette lighter plug 5.5mm plug into the electric jack on the 5.5mm plug seat.
⑷ use the operation: to determine the first few steps to do a good job, you can start the lifting operation.
Hold the remote control and press the button on the remote control as needed. "△" means rising, "▽" means descent, "□" means stop. )
⑸ in the process of jacking up, should carefully observe the jacking dynamic, to ensure that the electric jack is
not tilted until the wheel and the ground away from the 20mm, the wheels can be free to stop when lifting, replace the tires.
2, the use of electric wrench:
⑴ When the replacement wheel leaves the ground, connect the electric wrench
to the power supply (insert the 5.5mm power plug on the electric wrench directly into the 5.5mm plug of the cigarette lighter plug).
(2) Select the appropriate sleeve, the square hole into the top of the electric wrench on the square head, you can release or tighten the bolt.
⑶ according to the required direction of work, choose loose, tight switch. The left side of the power switch "‖", is the reverse direction, the right sign "|", is the direction of the forward, the middle mark "○", is stopped. With the thumb to hold the corresponding direction switch, hear 1-2 times "despair,
despair" after the crash can release the thumb, the whole process about 2-3 seconds.
1 X Electric Jack
1 X Electric Wrench
1 X Manual Remote Control
1 X Remote Control
1 X Battery Power Cable
2 X Double-Headed Sleeve (17-19 21-23)
3 X Spare Fuse
1 X Hand Crank
1 X Crowbar
1 X Cigarette Lighter Power Cable
1 X Pair Of Gloves
1. Easy to operate and convenient to carry around.
2. Connected to various types of smartphone, tablet, laptop and PC.
3. This wifi wireless endoscope camera can work with Android and IOS mobile device.
You just need install the APP, then do wifi connection with the endoscope camera, then
you can check the image via the 8mm lens. It have 6leds and the brightness is adjustable.
4. It can be used for underwater camera, waterproof Micro-cameras, motor vehicle detector,
sewer pipeline detector and so on.
Resolution: HD 720P
View Angle: 70 degree
Camera: 2.0 mega pixel
Focal Distance: 4-6cm (the best)
Camera Head Diameter: 8.0mm
Light: 6 adjustable white LED Lights
Waterprrof Level: IP67
Transmission Distance: 5-30M
Support System: IOS/ Android/ Windows/ Mac
1 X Endoscope
1 X Wifi Box
1 X Charging Line
1 X Fixed Set
1 X Side Mirror
1 X Hook
1 X Magnet
1 X Sucker
1 X User Manual
As a spare parts, you can repair at any time, easy to operate.
Car audio doors and windows disassembly tools.
Material: ABS plastic
Standard: Hand operated tools
Applicable: Home, Auto repair, Mechanical repairs, Doors and windows wedges
1 X Air Pump Wedge
To prevent car paint of oxidation and aging, Corrosion preventive, Resistant of high temperature, Anti-scratch, Easy to clean, Strong
toughness and extensibility, Water-repellency, Environmental protection.
Material: Silicon dioxide
Main scope of application:Car Paint Surface Plating Crystal
Liquid Content: 30ML
Cloth Size: about 10x10cm
Sponge Size: about 8.3x3.8x1.4cm
[Conversion: 1cm=0.3937 inch, 1inch=2.54 cm]
How To Use:
1.Clean the car and place the car in a place that will not be exposed to direct sunlight.
2.With the Open Wax Degreasing Agent sprayed on the towel to wipe the car paint, after the paint is dried, start the construction of
3.With the Plating Crystal cloth cover up the Plating Crystal Sponge to as a construction tool, and then use the Plating Crystal Primary
Liquid drops in the construction tools. In the earlier stage, Coating Crystal tools is dry, it is recommended to drop a few more drops. In
the later stage, it is recommended to drop 3-5 drops, to construct 40cmx40cm area.
4.Plating Crystal order: front cover - car roof - rear cover - rear car door - front bumper - rear bumper.
5.Wait for about 5 minutes, with your fingers to dip the crystal, if there are astringent feeling (similar to glue) and you can start to wipe.
6.Use the clean towel to wipe in the car paint surface and until car paint become bright. After finishing wiping, check whether there are
the omissions, if there are the omissions, just make up it is ok.
1 X Car Paint Plating Crystal Care Kit
1. Colored coded for easy size identification.
2. Separate fittings on fuel lines, fuel filters & fuel tank return lines.
3. Separates automatic transmission oil cooler lines on escort with AXOD and ATX transmissions.
4. Fits any 1/4" 5/16" or 3/8", 1/2" fuel line found on GM, Ford or Chrysler cars etc.
5. Disconnect tool allows quick separation of quick connectors found on radiators, transmissions and power steering lines
6. Releases the fingers on transmission-to-radiator oil cooler line easily without damage to the hose or connector .
7. Quick disconnect coupler tool slides down the line and into the connector separating the clip apart without damaging the quick connect seals allowing removal of clip.
1/4" ,5/16" ,3/8" ,1/2"
25cm x 12cm x 5cm
1 X Fuel & Transmission Line Disconnect Tool Set (8Pcs)
10 X Rubber Fittings
Perfectly balanced pad for optimum control.
Increased stability from Dual Density design allows improved control on curved panels
Less foam movement minimizes haze and micro marring.
Pad design allows for quick cleaning and drying.
Color: Red (For Finish Polish)
Orange (For Heavy Cut)
Blue(For Light Cut)
Perfect for use on Rupes Random Orbital, LHR15ES or
other polishers with a large orbit
1 X Polishing Pad
1.This removal installation tool can prevent your car from scratching and damaging.
2.Steel parts to last a lifetime
3.No breakable plastic parts
4.Easy to carry and convenient to use, just put in your car.
Color: Silver & Yellow
Applicable to the maintenance of the car access tools
12 X Car Panel Removal Open Pry Tools Kit
1. Dent Lifter for Baking-varnish-free dent repair, Paintless, Fast, Economy.
2. Slide hammer is more powerful for Paintless Dent Repair, conquer big dent.
3. Different tabs for different dent lifter or the Slide Hammer, Works with All Glue Pullers.
4. Aluminum PDR knockdown is long x diameter and is knurled for easy gripping.
5. PDR dent puller is designed to repair auto body small damage easily by manual operation.
It is environmental protection and does not damage the original paint. -With the dent puller, you
can remove the dent and restore your car to its original condition all by yourself. It should be applied
in combination with glue tabs and other PDR tools.
Dent lifter size: 100*80*125mm(approx)
Glue gun size: 190*160mm(approx)
The dent lifter is ideal for hail damage repair. Not applicable on vehicles with serious dent damage,
or that have been repainted as glue may remove non-factory clear coat.
1 X Dent Lifter
1 X Glue Gun
1 X Short T-bar
1 X Scraper
1 X Tap Down
1 X Repair Bar
1 X Alcohol Bottle
1 X Tool Bag
6 X Pro Glue Sticks
22 X Tabs(10 Red+12 Black)
Glue Tool Dimension: Approx. 19.3x16.3x3cm/ 7.60x6.41x1.18''
Working Power: 60W
Working voltage: 110v-240v, 50/ 60Hz
Plug Type: US plug (Sent with an adapter according your country)
PDR pulling bridge works on virtually any flat, non-porous surface
Puller tap have different sizes suitable for various sizes of dents
it can repair different dents for car, such as hail damage, collision damage and other dents
It doesn't hurt car original paint
Very easy to operate. you can enjoy the DIY fun
Save money , you do not need to go to 4S shop to paying for much money for repairing
Multi-function: for car dent repair / toys and models / artificial flowers / plumbing/ furniture/ cardboard and much more
Length: Approx. 27cm/ 10.63'', diameter: Approx. 1.1cm/ 0.43''
Special feature: our glue sticks are professional design for repairing car dent. has very strong adhesion. if you want to
repair car dent, it is your best choice.
Transparent glue: For the Japanese brand cars whose paints are thinner than other brand cars, it could work on high
or low temperature
Yellow glue: For the Europe and America brand cars, there is an unique advantage on its car body for its paint is very
thick and solid, and it’s more ideal to deal with the small dent
Black one:it could be used for all cars and it is better to work on the temperature over 20°
1 X Hot Melt Glue Tool
1 X Puller Bridge
5 X Black Glue Sticks
5 X White Glue Sticks
5 X Yellow Glue Sticks
1 X Empty Bottle
2 X Shovels
1.For baking varnish free removal works, paintless, fast, economy.
2.Car charger glue gun -power supply from the car no need to add additional socket directly.
3.Various size tabs for dent lifter or slide hammer for all glue strippers.
4.PDR accessories of metal and nylon blow down set, different head for different bumps.
5.Popular PDR pulling bridge Works on virtually any flat, non-porous surface.
6.Easilly controlled ,remove the dent by yourself with PDR pulling bridge.
7.Puller tap have different sizes suitable for various sizes of dents.
AC 100-240V 50/60Hz
Glue gun power
1 X Slide Hammer
1 X Repair Hammer
1 X Car Charger Glue Gun
1 X Matel Tap down Pen With 5 Heads
1 X White Tap down
1 X Ruller Bridge+4pcs Different Head
1 X Rose Red T-bar
2 X Plastic Scoop
10 X Rose Red Glue Puller Tabs
10 X Glue Sticks
18 X Blue Glue Puller Tabs
Your shopping cart is empty!